
This SDK has been patched by Embedded Artists for the iMXRT1062 Developer's Kit.
The SDK was released on 2022-11-18 and is based on NXP's 2.12.1 SDK (SDK_2_12_1_MIMXRT1062xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* Flash settings (speed, algorithm, size, driver) to work with the 4MB OctalSPI ATXP032
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Modified pin muxing
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Adjusted the USB interface number for USB Host examples (it is different for host and device examples)
* Added a software_reset() function in board.c/.h to issue a JEDEC reset before NVIC_SystemReset()
* Changed the Wi-Fi examples to use the Embedded Artists 1XK M.2 Module (EAR00385) as default
* Many of the projects have been updated to use a more complete pin_mux.c file where all
  necessary pins have been initialized. The SDK examples used to only configure the pins
  that they use (and often not every pin) and most of the time the configuration was only
  for MUX:ing and not the PAD settings (pull up/down/none, drive strength and slew).
* Embedded Wizard project 'ew_gui_smart_thermostat' was incorrectly setup for EVKB
* Changed the default display to RK043FN02H as it is the one mounted on the Developer's Kits

This has been added:
* New WDOG examples that work
* I2C probe example
* Example to show the use of software_reset()

This has been removed:
* All projects for the EVK - only keeping EVKB which is then patched
* The original WDOG and RTWDOG examples as those were not working

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1060.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work

Connectors:
* J22 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
The flexio_i2s_interrupt example shows how to use flexio_i2s driver with interrupt:

In this example, flexio acts as I2S module to record data from codec line and playbacks the recorded data at the same time using interrupt.

Toolchain supported
===================
- IAR embedded Workbench  9.30.1
- Keil MDK  5.37
- GCC ARM Embedded  10.3.1
- MCUXpresso  11.6.0

Hardware requirements
=====================
- Mini/micro USB cable
- MIMXRT1060-EVKB board
- Headphone(OMTP standard)
- Personal Computer

Board settings
==============
- J34, headphone connected
- connect FLEXIO pins to the pad close to J23 as follows:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Pin Name   Board Location     Pin Name    Board Location
RX_DATA    J16-1              RX_DATA     J23-11
TX_DATA    J16-2              TX_DATA     J23-17
SYNC       J33-4              SYNC        J23-16
BCLK       J33-3              BCLK        J23-23
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Prepare the Demo
================
1.  Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
2.  Open a serial terminal with the following settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3.  Download the program to the target board.
4.  Either press the reset button on your board or launch the debugger in your IDE to begin running the example.

Running the demo
================

Note: This demo uses both headphone mic and board main mic(P1) as input source. The headphone mic provides left
channel data, and main mic (P1) provides right channel data. If users found there is noise while do record operation,
most probably it is the headphone standard issue (OMTP and CTIA standard difference). You should use the OMTP
standard headphone. You can disable the left channel by using an headphone without microphone feature.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

When the demo runs successfully, the log would be seen on the OpenSDA terminal like as below.

~~~~~~~~~~~~~~~~~~~~~
FLEXIO_I2S interrupt example started!

FLEXIO_I2S interrupt example finished!
~~~~~~~~~~~~~~~~~~~~~

Note:
This example's right/left channel data is swapped due to the buffer maintain issue. This issue will be fixed in later release.
