
This SDK has been patched by Embedded Artists for the iMXRT1062 Developer's Kit.
The SDK was released on 2022-11-18 and is based on NXP's 2.12.1 SDK (SDK_2_12_1_MIMXRT1062xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* Flash settings (speed, algorithm, size, driver) to work with the 4MB OctalSPI ATXP032
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Modified pin muxing
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Adjusted the USB interface number for USB Host examples (it is different for host and device examples)
* Added a software_reset() function in board.c/.h to issue a JEDEC reset before NVIC_SystemReset()
* Changed the Wi-Fi examples to use the Embedded Artists 1XK M.2 Module (EAR00385) as default
* Many of the projects have been updated to use a more complete pin_mux.c file where all
  necessary pins have been initialized. The SDK examples used to only configure the pins
  that they use (and often not every pin) and most of the time the configuration was only
  for MUX:ing and not the PAD settings (pull up/down/none, drive strength and slew).
* Embedded Wizard project 'ew_gui_smart_thermostat' was incorrectly setup for EVKB
* Changed the default display to RK043FN02H as it is the one mounted on the Developer's Kits

This has been added:
* New WDOG examples that work
* I2C probe example
* Example to show the use of software_reset()

This has been removed:
* All projects for the EVK - only keeping EVKB which is then patched
* The original WDOG and RTWDOG examples as those were not working

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1060.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work

Connectors:
* J22 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


This example has been configured to use the 1XK M.2 module. To change which
module to use, replace WIFI_IW416_BOARD_MURATA_1XK_M2 in the app_config.h file
with one of the following and then rebuild the project:

    WIFI_IW416_BOARD_MURATA_1XK_M2     - To use the 1XK M.2 module
    WIFI_88W8801_BOARD_MURATA_2DS_M2   - To use the 2DS M.2 module
    WIFI_88W8987_BOARD_MURATA_1ZM_M2   - To use the 1ZM M.2 module

The NXP EVK needs an 'Murata uSD M.2 Adapter' but the iMXRT1062 Developer's Kit
has an M.2 connector (J38) so the adapter is not needed. Please ignore all mentions
of the 'Murata uSD M.2 Adapter' and the 'receptable cables' below.

More information about the M.2 Modules can be found here: https://www.embeddedartists.com/m2/.

Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
This is the Wi-Fi Test mode example to demonstrate the test mode support usage.

Before building the example application select Wi-Fi module macro in the app_config.h. (see #define WIFI_<SoC Name>_BOARD_<Module Name>).
For more information about Wi-Fi module connection see:
    readme_modules.txt
    Getting started guide on supported modules configuration:
    https://www.nxp.com/document/guide/getting-started-with-nxp-wi-fi-modules-using-i-mx-rt-platform:GS-WIFI-MODULES-IMXRT-PLATFORM



Toolchain supported
===================
- IAR embedded Workbench  9.30.1
- Keil MDK  5.37
- GCC ARM Embedded  10.3.1
- MCUXpresso  11.6.0

Hardware requirements
=====================
- Micro USB cable
- evkbmimxrt1060 board
- Personal Computer


Board settings
==============


Prepare the Demo
================
1.  Connect a micro USB cable between the PC host and the CMSIS DAP USB port on the board
2.  Open a serial terminal with the following settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3.  Connect the WiFi module to SD card slot.
4.  Download the program to the target board.
5.  Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo
================
1. Add CLI init API in applications main function.
2. Add WLAN CLI init API once WLAN Connection Manager gets initialized correctly.
3. When the demo starts, a welcome message would appear on the terminal, press enter for command prompt:
   Press tab or type help to list out all available CLI commands.

wifi test mode demo
Initialize CLI
Initialize WLAN Driver
MAC Address: 00:13:43:91:8A:3D 
[net] Initialized TCP/IP networking stack
app_cb: WLAN: received event 10
app_cb: WLAN initialized
WLAN Test Mode CLIs are initialized
CLIs Available:

help 
wlan-version 
wlan-mac 
wlan-set-rf-test-mode 
wlan-set-rf-channel <channel>
wlan-get-rf-channel 
wlan-set-rf-band <band>
wlan-get-rf-band 
wlan-set-rf-bandwidth <bandwidth>
wlan-get-rf-bandwidth 
wlan-get-rf-per 
wlan-set-rf-tx-cont-mode <enable_tx> <cw_mode> <payload_pattern> <cs_mode> <act_sub_ch> <tx_rate>
wlan-set-rf-tx-antenna <antenna>
wlan-get-rf-tx-antenna 
wlan-set-rf-rx-antenna <antenna>
wlan-get-rf-rx-antenna 
wlan-set-rf-tx-power <tx_power> <modulation> <path_id>
wlan-set-rf-tx-frame <start> <data_rate> <frame_pattern> <frame_len> <adjust_burst_sifs> <burst_sifs_in_us> <short_preamble> <act_sub_ch> <short_gi> <adv_coding> <tx_bf> <gf_mode> <stbc> <bssid>

# 
# wlan-set-rf-test-mode
RF Test Mode configuration successful

# 
# wlan-set-rf-channel 6
Channel configuration successful

# wlan-get-rf-channel
Configured channel is: 6

# wlan-set-rf-band 0
RF Band configuration successful

# wlan-get-rf-band
Configured RF Band is: 2.4G

# wlan-set-rf-bandwidth 0
Bandwidth configuration successful

# wlan-get-rf-bandwidth
Configured bandwidth is: 20MHz

# 
# wlan-get-and-reset-rf-per
PER is as below: 
  Total Rx Packet Count                    : 3
  Total Rx Multicast/Broadcast Packet Count: 3
  Total Rx Packets with FCS error          : 2

# wlan-set-rf-tx-antenna 1
Tx Antenna configuration successful

# wlan-get-rf-tx-antenna
Configured Tx Antenna is: Main

# wlan-set-rf-rx-antenna 2
Rx Antenna configuration successful

# wlan-get-rf-rx-antenna
Configured Rx Antenna is: Aux

# wlan-set-rf-tx-power 8 1 1
Tx Power configuration successful
  Power         : 8 dBm
  Modulation    : OFDM
  Path ID       : PathB

# wlan-set-rf-tx-frame 1 7 2730 256 0 0 0 0 0 0 0 0 0 ad:ad:23:12:45:57
Tx Frame configuration successful
  Enable                    : enable
  Tx Data Rate              : 7
  Payload Pattern           : 0x00000AAA
  Payload Length            : 0x00000100
  Adjust Burst SIFS3 Gap    : disable
  Burst SIFS in us          : 0 us
  Short Preamble            : disable
  Active SubChannel         : low
  Short GI                  : disable
  Adv Coding                : disable
  Beamforming               : disable
  GreenField Mode           : disable
  STBC                      : disable
  BSSID                     : AD:AD:23:12:45:57 

