
This SDK has been patched by Embedded Artists for the iMXRT1064 Developer's Kit.
The SDK was released on 2021-12-01 and is based on NXP's 2.10.0 SDK (SDK_2_10_0_MIMXRT1064xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Wi-Fi and Bluetooth projects
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Added an I2C driver for the PWM gpio expander (PCA9530) and code to use it
* Modified pin muxing
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Examples using a disaplay have been updated to use PCA6416/PCA9530 for
  RST/PWR/BL signals
* BOARD_USER_BUTTON has been redirected to SW5/WAKEUP button on the uCOM Carrier Board
* USER_LED has been changed to the blue RGB LED using PCA6416
* Adjusted the USB interface number (it is different for host and device examples)
* Added support for Embedded Artists 2DS M.2 Module (EAR00386) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1ZM M.2 Module (EAR00364) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1XK M.2 Module (EAR00385) in the NXP Wi-Fi examples
* Changed reset pin for SD card examples

This has been added:
* LWIP projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AWS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AzureRTOS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* I2C probe example
* Wi-Fi (serial) examples for the CMWC1ZZABR-107-EVB (a.k.a ABR Module)

This has been removed:
* All projects for the expansion board AGM01

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1064.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work



Connectors:
* J29 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THIS PROJECT IS NOT DIRECTLY COMPATIBLE WITH THE HARDWARE AND WILL NOT WORK.

The I2C chip accessed in this example is not mounted on the uCOM Carrier Board
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!



Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
The bubble level demo demonstrates basic usage of the on-board accelerometer to implement a bubble level. A bubble
level utilizes two axes to visually show deviation from a level plane (0 degrees) on a given axis.

The following files are generated by MCUXpresso Config Tools:
- bubble_peripheral.mex: This mex file contains pin/clock/peripheral settings of this example. User can modify the settings in config tool and generate new source file for pin/clock/peripheral.
- peripheral.c/.h: These files are generated by MCUXpresso peripherals tool which could be imported back to the tool.
- clock_config.c/.h: These files are generated by MCUXpresso clocks tool which could be imported back to the tool.
- pin_mux.c/.h: These files are generated by MCUXpresso pins tool which could be imported back to the tool.


Toolchain supported
===================
- IAR embedded Workbench  9.10.2
- Keil MDK  5.34
- GCC ARM Embedded  10.2.1
- MCUXpresso  11.4.0

Hardware requirements
=====================
- Mini/micro USB cable
- EVK-MIMXRT1064 board
- Personal Computer

Board settings
==============
No special settings are required.

Prepare the Demo
================
1.  Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
2.  Open a serial terminal with the following settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3.  Download the program to the target board.
4.  Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo
================

When the example runs successfully, you can see the similar
information from the terminal as shown below.

~~~~~~~~~~~~~~~~~~~~~
Welcome to the BUBBLE example

You will see the change of LED brightness when change angles of board

x=  6 y = 22
x=  8 y = 26
x= 10 y = 28
x= 10 y = 28
x= 11 y = 29
x= 11 y = 29
~~~~~~~~~~~~~~~~~~~~~

Note:
- If the user LED flashes constantly and the following message is printed on the console:
    Sensor device initialize failed!

    Please check the sensor chip U32

  please check if the combo sensor (U32) is presented on the board.
