
This SDK has been patched by Embedded Artists for the iMXRT1064 Developer's Kit.
The SDK was released on 2021-12-01 and is based on NXP's 2.10.0 SDK (SDK_2_10_0_MIMXRT1064xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Wi-Fi and Bluetooth projects
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Added an I2C driver for the PWM gpio expander (PCA9530) and code to use it
* Modified pin muxing
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Examples using a disaplay have been updated to use PCA6416/PCA9530 for
  RST/PWR/BL signals
* BOARD_USER_BUTTON has been redirected to SW5/WAKEUP button on the uCOM Carrier Board
* USER_LED has been changed to the blue RGB LED using PCA6416
* Adjusted the USB interface number (it is different for host and device examples)
* Added support for Embedded Artists 2DS M.2 Module (EAR00386) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1ZM M.2 Module (EAR00364) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1XK M.2 Module (EAR00385) in the NXP Wi-Fi examples
* Changed reset pin for SD card examples

This has been added:
* LWIP projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AWS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AzureRTOS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* I2C probe example
* Wi-Fi (serial) examples for the CMWC1ZZABR-107-EVB (a.k.a ABR Module)

This has been removed:
* All projects for the expansion board AGM01

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1064.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work



Connectors:
* J29 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
The flexio_i2s_EDMA example shows how to use flexio_i2s driver with EDMA:

In this example, flexio acts as I2S module to record data from codec line and playbacks the recorded data at the same time using EDMA.

Toolchain supported
===================
- IAR embedded Workbench  9.10.2
- Keil MDK  5.34
- GCC ARM Embedded  10.2.1
- MCUXpresso  11.4.0

Hardware requirements
=====================
- Mini/micro USB cable
- EVK-MIMXRT1064 board
- Headphone(OMTP standard)
- Personal Computer

Board settings
==============
- J12, headphone connected
- remove R98,R99,R100,R101 and connect FLEXIO pins to the pad close to U13 as follows:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Pin Name   Board Location     Pin Name    Board Location
RX_DATA    SW5-1              RX_DATA     U13-16
TX_DATA    SW5-2              TX_DATA     U13-14
SYNC       SW5-3              SYNC        U13-13
BCLK       SW5-4              BCLK        U13-12
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Prepare the Demo
================
1.  Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
2.  Open a serial terminal with the following settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3.  Download the program to the target board.
4.  Either press the reset button on your board or launch the debugger in your IDE to begin running the example.

Running the demo
================

Note: This demo uses both headphone mic and board main mic(P1) as input source. The headphone mic provides left
channel data, and main mic (P1) provides right channel data. If users found there is noise while do record operation,
most probably it is the headphone standard issue (OMTP and CTIA standard difference). You should use the OMTP
standard headphone. You can disable the left channel by using an headphone without microphone feature.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

When the demo runs successfully, the log would be seen on the OpenSDA terminal like as below.

~~~~~~~~~~~~~~~~~~~~~
FLEXIO I2S EDMA example started!

FLEXIO I2S EDMA example finished!
~~~~~~~~~~~~~~~~~~~~~
