
This SDK has been patched by Embedded Artists for the iMXRT1064 Developer's Kit.
The SDK was released on 2021-12-01 and is based on NXP's 2.10.0 SDK (SDK_2_10_0_MIMXRT1064xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Wi-Fi and Bluetooth projects
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Added an I2C driver for the PWM gpio expander (PCA9530) and code to use it
* Modified pin muxing
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Examples using a disaplay have been updated to use PCA6416/PCA9530 for
  RST/PWR/BL signals
* BOARD_USER_BUTTON has been redirected to SW5/WAKEUP button on the uCOM Carrier Board
* USER_LED has been changed to the blue RGB LED using PCA6416
* Adjusted the USB interface number (it is different for host and device examples)
* Added support for Embedded Artists 2DS M.2 Module (EAR00386) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1ZM M.2 Module (EAR00364) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1XK M.2 Module (EAR00385) in the NXP Wi-Fi examples
* Changed reset pin for SD card examples

This has been added:
* LWIP projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AWS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AzureRTOS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* I2C probe example
* Wi-Fi (serial) examples for the CMWC1ZZABR-107-EVB (a.k.a ABR Module)

This has been removed:
* All projects for the expansion board AGM01

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1064.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work



Connectors:
* J29 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
This GUI demo is developed with the Embedded Wizard GUI solution.

This project implements an application that shows a thermostat, which is 
rotatable to adjust the nominal and actual temperature.
While you can in-/decrease the nominal temperature, the actual temperature 
is continously getting closer to it by heating up or cooling down. Both 
temperature types are displayed by different needles or indicators.


This examples runs bare metal, but Embedded Wizard is also possible
to use with FreeRTOS. Our official Build Environments, that can be downloaded 
as described above, includes examples and demos that illustrate the integration 
of FreeRTOS and can be used for your reference.



In order create your own GUI application powered by the latest version of
Embedded Wizard that is suitable for the i.MX RT1064 Evaluation Kit, please
visit https://doc.embedded-wizard.de/getting-started-mimxrt1064-evk

For this example a simulation of the user interface is also available. 
It can be used under following link 
http://www.embedded-wizard.de/NXP-SDK-Examples/IMXRT1064-EVK/Dashboard/Simulation/ 
with any web browser. The simulation uses the JS/WebGL Embedded Wizard Platform Package.
For further information about Embedded Wizard, please visit our web site at
https://www.embedded-wizard.de/platforms/nxp/imx-rt


Toolchain supported
===================
- IAR embedded Workbench  9.10.2
- GCC ARM Embedded  10.2.1
- Keil MDK  5.34
- MCUXpresso  11.4.0

Hardware requirements
=====================
- Micro USB cable
- IMXRT1064-EVK board
- Personal Computer
- RK043FN02H-CT LCD board

Board settings
==============
1. Connect the RK043FN02H-CT board to J8.

Prepare the Demo
================
1.  Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
2.  Open a serial terminal with the following settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3.  Download the program to the target board.
4.  Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo
================
If this example runs correctly, the sample application is displayed on the LCD screen.
The log below shows the output of the sample application 'SmartThermostat' in the terminal window:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Initialize Realtime Clock...                 [OK]
Initialize Display...                        [OK]
Initialize Touch Driver...                   [OK]
Initialize Memory Manager...                 [OK]
Initialize Graphics Engine...                [OK]
Create Embedded Wizard Root Object...        [OK]
Create Embedded Wizard Viewport...           [OK]
---------------------------------------------
Target system                                IMXRT1064-EVK
Color format                                 RGB565
MemoryPool address                           0x8107F800
MemoryPool size                              14157824 bytes
Framebuffer address                          0x81000000
Doublebuffer address                         0x8103FC00
Framebuffer size                             480 x 272
EwScreeenSize                                480 x 272
Graphics accelerator                         PXP
Vector graphics support                      enabled
Warp function support                        enabled
Index8 bitmap resource format                enabled
RGB565 bitmap resource format                enabled
Bidirectional text support                   enabled
Operating system                             none
External flash device                        none
Toolchain                                    <Toolchain name>
C-Compiler version                           <C-Compiler version>
Build date and time                          <MMM DD YYYY, HH:MM:SS>
Runtime Environment (RTE) version            10.00
Graphics Engine (GFX) version                10.00
Max surface cache size                       8388608 bytes
Glyph cache size                             256 x 256
Max issue tasks                              100
Surface rotation                             0
---------------------------------------------
