
This SDK has been patched by Embedded Artists for the iMXRT1064 Developer's Kit.
The SDK was released on 2021-12-01 and is based on NXP's 2.10.0 SDK (SDK_2_10_0_MIMXRT1064xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Wi-Fi and Bluetooth projects
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Added an I2C driver for the PWM gpio expander (PCA9530) and code to use it
* Modified pin muxing
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Examples using a disaplay have been updated to use PCA6416/PCA9530 for
  RST/PWR/BL signals
* BOARD_USER_BUTTON has been redirected to SW5/WAKEUP button on the uCOM Carrier Board
* USER_LED has been changed to the blue RGB LED using PCA6416
* Adjusted the USB interface number (it is different for host and device examples)
* Added support for Embedded Artists 2DS M.2 Module (EAR00386) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1ZM M.2 Module (EAR00364) in the NXP Wi-Fi examples
* Added support for Embedded Artists 1XK M.2 Module (EAR00385) in the NXP Wi-Fi examples
* Changed reset pin for SD card examples

This has been added:
* LWIP projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AWS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AzureRTOS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* I2C probe example
* Wi-Fi (serial) examples for the CMWC1ZZABR-107-EVB (a.k.a ABR Module)

This has been removed:
* All projects for the expansion board AGM01

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1064.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work



Connectors:
* J29 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
THIS PROJECT IS NOT DIRECTLY COMPATIBLE WITH THE HARDWARE AND WILL NOT WORK.

There is no CAN tranciever mounted on the uCOM Carrier Board
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!



Everything below this line is the original content of the readme file.
=======================================================================



Hardware requirements
=====================
- Mini/micro USB cable
- MIMXRT1064-EVK board
- 3.3V CAN transceiver
- Supported CAN interface (IXXAT, Vector, Kvaser, etc.)
- Personal Computer
- FreeMASTER 2.5 or later installed on PC

Board settings
==============
CAN transceiver is available on board, at pins J11

Prepare the demo
===============
1.  Connect a USB cable between the host PC and the Debug USB port on the target board.
2.  Connect CAN transceiver to CAN interface on PC. Make sure the CAN bus is properly terminated.
3.  Compile and download the program to the target microcontroller.
4.  Run and resume application execution when debugger stops in the main() function.

Connect with FreeMASTER
=======================
5.  Run FreeMASTER, use the Connection Wizard or open Project Options.
6.  Select FreeMASTER-over-CAN communication plug-in at 500kbps.
7.  Start communication, FreeMASTER loads the initial TSA Active Content links in the Welcome page.
8.  Click the "FreeMASTER Demonstration Project (embedded in device)" in the Welcome page.
9.  The demo is now running, you should be able to watch variable values and graphs.

More information
================
Read more information about FreeMASTER tool at http://www.nxp.com/freemaster.
Feel free to ask questions and report issues at FreeMASTER's 
community page at https://community.nxp.com/community/freemaster
