
This SDK has been patched by Embedded Artists for the iMXRT1064 Developer's Kit.
The SDK was released on 2022-03-15 and is based on NXP's 2.11.0 SDK (SDK_2_11_0_MIMXRT1064xxxxA.zip).

This is what has been patched:
* Set CPU speed according to Commercial/Industrial CPU
* Correction of the VDD_SOC_IN voltage.
* LWIP projects - added reading of the MAC address from the onboard I2C EEPROM
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Added an I2C driver for the PWM gpio expander (PCA9530) and code to use it
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Examples using a display have been updated to use PCA6416/PCA9530 for
  RST/PWR/BL signals
* BOARD_USER_BUTTON has been redirected to SW5/WAKEUP button on the uCOM Carrier Board
* USER_LED has been changed to the blue RGB LED using PCA6416
* Adjusted the USB interface number (it is different for host and device examples)
* Changed the Wi-Fi examples to use the Embedded Artists 1XK M.2 Module (EAR00385) as default
* Added support for Embedded Artists 1ZM M.2 Module (EAR00364) in the NXP Wi-Fi examples
* Many of the projects have been updated to use a more complete pin_mux.c file where all
  necessary pins have been initialized. The SDK examples used to only configure the pins
  that they use (and often not every pin) and most of the time the configuration was only
  for MUX:ing and not the PAD settings (pull up/down/none, drive strength and slew).
* Changed reset pin for SD card examples

This has been added:
* LWIP projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AWS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* AzureRTOS projects - option to use 100/10Mbps Ethernet-PHY Adapter
* I2C probe example
* Wi-Fi (serial) examples for the CMWC1ZZABR-107-EVB (a.k.a ABR Module)

This has been removed:
* All projects for the expansion board AGM01

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for EVK-MIMXRT1064.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work


Connectors:
* J29 (micro USB) is the default UART and unless specified otherwise it is setup for 115200 8/N/1


Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
The lpuart_9bit_interrupt_transfer example shows how to use lpuart driver in 9-bit mode in multi-slave system.
Master can send data to slave with certain address specifically, and slave can only receive data when it is addressed.

In this example, one lpuart instance is used with address configured. Its TX and RX pins are connected together.
First it sends a piece of data out, then addresses itself, after that sends the other piece of data. Only data
sent after the address can be received by itself.

Toolchain supported
===================
- IAR embedded Workbench  9.10.2
- Keil MDK  5.34
- GCC ARM Embedded  10.2.1
- MCUXpresso  11.5.0

Hardware requirements
=====================
- Mini/micro USB cable
- EVK-MIMXRT1064 board
- Personal Computer

Board settings
==============
Using instance 2 of LPUART interface to transfer data to itself.
TX pin is connected with RX pin.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
LPUART2     CONNECTS TO         LPUART2
Pin Name    Board Location      Pin Name  Board Location
TXD         J22-7               RXD       J22-8
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Prepare the Demo
================
1.  Connect a USB cable between the host PC and the OpenSDA USB port on the target board.
2.  Open a serial terminal with the following settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3.  Download the program to the target board.
4.  Either press the reset button on your board or launch the debugger in your IDE to begin running the demo.

Running the demo
================
When the demo runs successfully, the log would be seen on the OpenSDA terminal like:

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
USART 9-bit mode example begins
USART is configured with address, only data sent to itself after matched address can be received
USART will send first piece of data out:

0x 0  0x 1  0x 2  0x 3  0x 4  0x 5  0x 6  0x 7  
0x 8  0x 9  0x a  0x b  0x c  0x d  0x e  0x f  

USART will address itself
USART will send the other piece of data out:

0x10  0x11  0x12  0x13  0x14  0x15  0x16  0x17  
0x18  0x19  0x1a  0x1b  0x1c  0x1d  0x1e  0x1f  

USART received data:

0x10  0x11  0x12  0x13  0x14  0x15  0x16  0x17  
0x18  0x19  0x1a  0x1b  0x1c  0x1d  0x1e  0x1f  

All data matches!
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
