
This SDK has been patched by Embedded Artists for the iMXRT1176 Developer's Kit.
The SDK was released on 2022-03-02 and is based on NXP's 2.11.0 SDK (SDK_2_11_0_MIMXRT1176xxxxx.zip).

This is what has been patched:
* LWIP projects - added reading of the MAC address from I2C EEPROM either on the 100Mbit adapter
  or on the uCOM board
* Added an I2C driver for the gpio expander (PCA6416) and code to use it
* Added an I2C driver for the PWM gpio expander (PCA9530) and code to use it
* SDRAM size has been corrected to 32Mb (including linker files, MPU and DCD)
* 1G Ethernet PHY has been changed from RTL8211F to AR8031DS
* SEMC projects - changed to correct settings for the SDRAM
* SEMC projects - changed algorithm for memory test and now test entire 32MB instead of only 4KB
* Examples using eLCDIF/LCDIFv2 have been updated to use PCA6416/PCA9530 for
  RST/PWR/BL signals
* BOARD_USER_BUTTON has been redirected to SW5/WAKEUP button on the uCOM Carrier Board
* USER_LED has been changed to the blue RGB LED using PCA6416
* Touch: I2C bus and GPIOs have been changed for RST/INT
* Camera pins
* Adjusted the USB interface number (it is different for host and device examples)
* Changed the Wi-Fi examples to use the Embedded Artists 1XK M.2 Module (EAR00385) as default
* Corrected the ethernet PHY addresses
* Changed CORE clock depending on speed grading of MCU (798MHz for Industrial, 996MHz for Commercial)
* Changed SEMC clock to be within maximum speed for SDRAM (now 148.5MHz, was 198MHz)
* Many of the projects have been updated to use a more complete pin_mux.c file where all
  necessary pins have been initialized. The SDK examples used to only configure the pins
  that they use (and often not every pin) and most of the time the configuration was only
  for MUX:ing and not the PAD settings (pull up/down/none, drive strength and slew).
* Converted the AzureRTOS examples to use the BOARD_NETWORK_USE_100M_ENET_PORT (same as all
  other networking examples) instead of using the old EXAMPLE_USE_1G_ENET_PORT

This has been added:
* HDMI support to most GUI examples. HDMI at 1024x768@60 is the default resolution but
  that can be changed per project in display_support.h/elcdif_support.h/lcdifv2_support.h.
* Added ADT example for TensorFlow Lite
* I2C probe example
* EDID reader example
* Wi-Fi (serial) examples for the CMWC1ZZABR-107-EVB (a.k.a ABR Module)

This has been removed:
* All projects for the expansion board AGM01

Important things to note:
* Read section "8 - Known Issues" in docs/MCUXpresso SDK Release Notes for MIMXRT1170-EVK.pdf
  to see known issues with the current version of the SDK.
* For Iperf examples, set compiler optimization to -O3 or similar to improve performance.
* If the hardware seems unresponsive and the debugger cannot connect/flash/erase the current program
  then the most likely cause is the running program preventing the access. To stop the currently
  running program and regain control:
  1) Press and hold down the ISP_ENABLE button (SW1)
  2) Press and hold down the RESET button (SW3)
  3) Let go of the RESET button
  4) Wait an extra second or two
  5) Release the ISP_ENABLE button
  6) The hardware is now in a mode where programming/erasing it should work


Connectors:
* J29 (micro USB) is the default UART for the CM7 core and unless specified otherwise it is setup for 115200 8/N/1
* J30 (micro USB) is the default UART for the CM4 core and unless specified otherwise it is setup for 115200 8/N/1
* For 1Gbit Ethernet examples, use connector J25 on uCOM Carrier Board
* For 100Mbit Ethernet examples, use ethernet adapter connected between J12 on uCOM Carrier Board
  and J37 on the adapter. These four connections are also needed:
    1) uCOM Carrier Board, JP38:1 -> adapter JP37:1
    2) uCOM Carrier Board, JP38:2 -> adapter JP37:2
    3) uCOM Carrier Board, JP27:1 -> adapter JP39:2
    4) uCOM Carrier Board, JP27:2 -> adapter JP39:1
* The two CSI examples can use either an OV5640 camera in connector J23 or a camera in connector J24
* The EIQ examples that use a camera expects the camera in connector J24 (J23 might work for some
  of the examples but runs much slower)
* Some GUI examples are configured for the RK055AHD091 display which should be in connector "C" on
  the uCOM Carrier Board. Ignore the readme text about connecting extra 5V power.
* The default for GUI examples is to use an HDMI adapter in connector "C" on
  the uCOM Carrier Board. Ignore the readme text about connecting extra 5V power.


Everything below this line is the original content of the readme file.
=======================================================================



Overview
========
The flexio_spi_master_edma_lpspi_slave example shows how to use flexio spi master driver in edma way:

In this example, a flexio simulated master connect to a lpspi slave .



Toolchain supported
===================
- IAR embedded Workbench  9.10.2
- Keil MDK  5.34
- MCUXpresso  11.5.0
- GCC ARM Embedded  10.2.1

Board settings
==============
Remove 0Ω resistor to R200,R406,R408,R404.

To make the example work, connections needed to be as follows:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
        SLAVE           connect to      MASTER
Pin Name   Board Location     Pin Name    Board Location
SOUT       J10-10               SIN       J26-6
SIN        J10-8                SOUT      J26-4
SCK        J10-12               SCK       J26-2
PCS0       J10-6                PCS0      J26-8
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Prepare the Demo
================
1. Connect a mini USB cable between the PC host and the OpenSDA USB port on the board.
2. Open a serial terminal on PC for OpenSDA serial device with these settings:
    - 115200 baud rate
    - 8 data bits
    - No parity
    - One stop bit
    - No flow control
3. Download the program to the target board.
4. Either press the reset button on your board or launch the debugger in your IDE to begin running
   the demo.

Running the demo
================
You can see the similar message shows following in the terminal if the example runs successfully.

~~~~~~~~~~~~~~~~~~~~~~~~~~~~
FLEXIO Master edma - LPSPI Slave interrupt example start.

This example use one flexio spi as master and one lpspi instance as slave on one board.

Master uses edma and slave uses interrupt way.

Please make sure you make the correct line connection. Basically, the connection is:

FLEXIO_SPI_master -- LPSPI_slave

      CLK        --    CLK

      PCS        --    PCS

      SOUT       --    SIN

      SIN        --    SOUT

This is LPSPI slave call back.

FLEXIO SPI master <-> LPSPI slave transfer all data matched!

End of example.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Note
This case use flexio to simulate spi protocol, 

Owing to this simulate process is software and executed in qspi_flash for flexspi_nor target, 

but external flash's speed can not support to the rate of SPI transmit because of effected by performance. 

So the settings for baudrate of transmission do not more than 150k
